Railing flank for lateral stairs S

Tecrostar mezzanines and stairs are supplied with everything you need to install the kit at its maximum surface area or height.

• All the beams and columns
• The floor panels
• All the nuts and bolts
• Wall anchors
• Assembly manual
• Anchors for anchoring the columns to the floor

Personalised phone or email service from our specialists

You can choose between several types of stairs:

• Straight stairs

• Spiral stairs

• Ladders

• Retractable ladders

• Alternating tread stairs

The stairs can be placed in different positions, increasing the possible configurations

Case 1: Exterior stairs, perpendicular to the mezzanine.

Case 2: Interior stairs. You will need a beam for interior stairs.

Case 3: Exterior stairs, parallel to the mezzanine. You will need a stair landing.

Case 4: A different placement to our mezzanines.

Yes, provided that the height matches. All our stairs can be located in any of our structures. As the structures, the stairs are height-adjustable. We have several different types of stairs, to ensure the height compatibility with the selected mezzanine.

Yes, our products can be installed outdoors, although you should bear in mind a series of special considerations and carry out maintenance of the material to guarantee that they are in good condition. See this section for more details

Yes. They can be installed on a surface that is not a Tecrostar surface. The customer must bear in mind that they are responsible for the strength of the joint and structure to which they are anchored.

If you need to anchor the stairs to a structure that is not a Tecrostar structure, see the following details about the anchors:

Anchor A

References that have this anchor: 30501, 30401, 31003, 31301, 31102

Anchor B:

References that have this anchor: 30303-0

Anchor C:

References that have this anchor: 30601, 30801

The minimum width is 29 3/8" and the maximum is 45 1/8". The length should be more than 51 1/8".

No, it can’t. This kit is specially designed to be used with our staircases.

It depends on the use. The regulation is for stairs for common use and our stairs are for private use. Our stairs that comply are the 42^nd: Long Stair M  and  L Stair

The anchor that joins the stairs to the mezzanine can attach the stairs with 4 or 2 screws. If you choose the configuration of just 2 screws, the stairs can pivot. In any case, the stairs have the same resistance.

Yes, the direction of rotation can vary.

Each model of stairs has an inclination and it cannot be changed unless otherwise stated. You must choose the stairs that best suit your needs.

The stairs include the maximum number of steps that are required in their maximum heights. The more the height is reduced, the less steps will be installed. However, you can acquire additional steps as spare parts, the number of steps is designed according to the inclination of each staircase though. An excessive number of steps would reduce the going available for treading, specially important when going down.

Yes, the railing of both sides of the stairs is removable and, therefore, it can be taken off. However, Tecrostar recommends to install it for security and because they provide rigidity to the stairs as well. On the other hand, the stairs include the railing; it is not possible to acquire them without the railing.

For the orders that include just the stairs, the dimensions of the package are:

Length: 92 1/2"

Width: 12 1/2"

Height: 12 1/4"

The weight depends on the model of the stairs. Check the product sheet.

Yes. You will have to acquire the beam for interior stairs.

Check the the table with the specifications of each staircase to get this information.

No, you can’t.

No, they are not. However, there are other possible combinations between ranges, in which the performance and configuration of the standard product changes (see diagram).

Low railing:

Compatible with mezzanines of the S, M and L ranges. To go ahead with the installation, you must purchase one angular strut from the corresponding mezzanine range for each railing post.

Compatible with the mezzanines of the XL range. To go ahead with the installation, you must purchase one M/L angular strut and one Adapter for Accessories in Primary Beam XL for each railing post.

Loft bed railing S, Railing S, 4-Tubes railing S and Panel railing S:

Compatible with S range mezzanines: No additional accessories are required.

Compatible with the M and L range mezzanines: To go ahead with the installation, you must purchase one M/L angular strut for each railing post. Please note that the height of the handrail is reduced.

Compatible with the mezzanine of the XL range: To go ahead with the installation, you must purchase one M/L post clamp and one Adapter for Accessories in Primary Beam XL for each handrail post. Please note that the height of the railing is reduced.

Railing M, 4-Tubes railing M and Panel railing M:

These are not compatible with S range mezzanines.

Compatible with the M and L range mezzanines: No additional accessories are required.

Compatible with the XL range mezzanines: To go ahead with the installation, you must purchase one Adapter for Accessories in Primary Beam XL for each railing post.

Railing with safety skirting board L and Public use railing L:

These are not compatible with S range mezzanines.

Compatible with the M and L range mezzanines: No additional accessories are required.

Compatible with the XL range mezzanines: To go ahead with the installation, you must purchase one Adapter for Accessories in Primary Beam XL for each railing post.

Railing with safety skirting board XL:

These are not compatible with S range mezzanines.

Compatible with the M, L and XL range mezzanines: No additional accessories are required.

All TecroStar railings are designed for installation on our mezzanines. The Railing with safety skirting board XL is the most recommended for installation on other surfaces.

This is not recommended, as to cover a space with reduced height (i.e.: attics, irregular/low ceilings, etc.) we recommend installing the Low Railing instead. This particular railing model will allow the height of the railing posts to be adjusted to the client's taste.

That depends. The railing kits are 78 3/4" long. You will have to calculate how many kits you need.

The handrails of the railing* and the stairs** are available in aluminium with the following finishes:

• Silver anodized (without additional cost)

• Black lacquered (additional cost)

• Wooden effect (additional cost)

In all cases it is suitable for outdoor use.

* The handrail of the loft bed railing is made of beech plywood.

** The spiral stairs have necessarily high-density polyethylene (HDPE) handrails in black colour.

To install Tecrostar mezzanines you need 2 adults (they do not need to be DIY experts). It is recommendable to use personal safety equipment like gloves, boots, etc. in order to avoid accidents.

When installing range L mezzanines you may need to use some type of scaffolding or ladder for working at heights and manual or electric lifting machinery to raise the primary beams, particularly if the structure is more than 3m high. The other ranges can be lifted easily by hand.

You will need the following tools to install the mezzanines: tape measure, some type of spanner for m10 and m8 bolts and a screwdriver (an electric screwdriver will make the task much easier), spirit level, drill and a tool for cutting the panels (saw, jigsaw, circular saw, etc.)

You can find all the tools required to assemble it and tested by Tecrostar in the tools section.

All the models are installed by following these steps:

Pre-assemble the structure on the floor in the desired area.

Raise the outer structure to the desired height.

Finish assembling the structure and floor.

You can do it yourself with the help of a friend. It is easily installed in a few hours, depending on the product.

TS8 Mezzanine: 3 hours with 2 people

TM15 Mezzanine: 4 hours with 2 people

TL30 Mezzanine: 5 hours with 3 people

The times are a guideline and for assembly only. You need to add the time it takes to measure up, move the components to the location, clean up, etc.

Once the product has left our facilities, the normal transport time is between 6 and 8 weeks. The transport time varies greatly and is difficult to control due to many factors: Place of delivery, local holidays, customs, etc.

If we cannot meet this delivery time, we will contact you.

Mezzanines are shipped in boxes by an external company in a lorry with a tail lift that enables the box to be unloaded to the ground (at street level at the customer’s address).

Depending on your order you can receive different packages: One box for the mezzanines of the S and M ranges or two boxes for L mezzanines.

Length: 94"

Width: 112"

Height: 21 1/4"

The stairs can share the box with the mezzanines if they are purchased at the same time or you can have a separate box for the stairs. Check the stairs section.

Don't be alarmed by the total weight of the product, the components are light and manageable, so you can move them easily and take them up in the lift.  The heaviest components are the primary beams from the L range (86 lb), the rest of the ranges are considerably lighter (26.5 lb). The floor panels are very light and fit in any lift. No component is more than 94 1/2" long and therefore, fits in most lifts.

Spiral Stairs

Ladders

Straight Stairs (private/domestic use)

Straight Stairs (public/industrial use)

Tecrostar products are manufactured with the most suitable materials for the proposed technical solutions, combining wood, steel and top quality aluminium.

• The steels used for beams, columns and other components are fit for structural uses with a high yield strength (S235, S275 or S3555, as required). The pieces are manufactured using maximum precision laser cutting, folding and pressing processes. Next a powder coating is applied and they are baked in the oven, offering maximum adhesion and an outstanding finish.
• Structure hardware grade 8.8
• Anodized aluminum apt for outdoor use
• The wood panels used for the mezzanine flooring can be made of European radiata pine plywood or high density structural chipboard. All the boards are tongue and groove on all four sides to prevent faults and unevenness at the joints of the modules.
• Other wooden components, such as the steps and parts of the handrails, are made from top quality beech.

TECRO has earned certification from the AEM, the federation of Spanish materials handling. We have also received a Gold Medal Award of Merit from the INPEX (Invention and New Product Exposition), the top award for innovation at the largest Invention Exposition in the USA.